A Specification for the Production of Petroleum Hoses outlines the requirements and parameters for their manufacture. This document includes the title, number, date, and several other sections. It also specifies how many feet a hose should be long and what the shelf life should be. It also details the length of petroleum hoses. Once a […]
A Specification for the Production of Petroleum Hoses outlines the requirements and parameters for their manufacture. This document includes the title, number, date, and several other sections. It also specifies how many feet a hose should be long and what the shelf life should be. It also details the length of petroleum hoses. Once a specification has been developed, it can be used to establish a standard for suppliers and manufacturers.
Specification for production of petroleum hoses
This specification covers the manufacture and use of a variety o petroleum hoses. The hoses are intended for transporting fuel, oil, and water. The hoses shall have a durable, high-quality outer coating and be uniform in quality. The hoses must be marked with a CAGE Code, date of cure, and specification. The markings shall be legible and repeated every six inches of the hose. Any hose not meeting the specifications will be rejected.
This specification lists the dimensional requirements of a hose. The dimensions are given in metric units and inches. The specification provides information about the material and the performance characteristics of the hose. The performance characteristics of a hose include visual examination, dimensional checking, and pressure. These requirements are listed in table I. The specification also lists the hydrostatic, proof, as well as burst pressures for a hose.
This specification also specifies the inner and outer layer thickness of the hose. The outer layer of the tube is made from synthetic rubber, which has been mixed with the required ingredients. The inner tube is made of a seamless material with a minimum thickness.040″ (1.02mm). It should not have pits and have an even, smooth surface. This specification is a good place to start when choosing a petroleum hose.
high temperature Specification for production of petroleum hoses manufacture
A high-temperature hose is essential in the oil and gas industry. These hoses can be used to transport fuel, oil products, and other liquids. Most of these liquids are aggressive and require a conduit hose to meet certain standards. The inner surface of the conduit hose must be made from a special material that can withstand the high temperatures and chemical impurities found in the media.
It is important to understand the design factors of a hose before selecting it. A hose designed to withstand 2500 psi pressure won’t rupture until it is exposed to 10000 psi pressure. However, a fabricator may use a higher design factor than is needed, causing a hose to fail at a higher pressure than it was originally designed for.
The system pressure must be equal or greater than the working pressures of a Hose Assembly. A hose assembly must pass at least one-half its MAWP. You can also have floating elbows, couplings and threaded connections in your hose assembly. A hose assembly that complies with these specifications is safe for use in a variety of high-temperature applications.
Specification for production of petroleum hoses length
The material used for the manufacture of petroleum hoses shall conform to the requirements of this Specification for Production of Petroleum Hoses (SAE-AS1933). The lining must be made of polychloroprene rubber and reinforced or coated. The material must have a minimum resistance value of 10 ohms, and be fully conductive. Hoses must have a minimum diameter of 10 feet (3.05m) and not exceed the MAWP specifications. Typical hose assembly features include steel or aluminum TTMA flanges, floating elbows, threaded connections, and couplers. Hoses must conform to EN 13765:2010 and shall be capable of enduring temperatures up to 100degC.
The elongation of a hose must not be less than 40% of the original elongation. Leakages in the exterior or interior of hoses are not allowed. The hoses must be capable of sustaining pressures up to 35 psi and be free of blowouts. They must be crush resistant, which means that they must not break or show cracks in the tube or coating.
The fittings at the end of a hose shall conform to the SAE-AS5131 or AS5132. End fittings shall be designed to facilitate servicing and inspection. The material used for the hoses shall be synthetic rubber compounded with the necessary ingredients. The inner tube shall be seamless and have a minimum thickness of.040 inch (1.02 mm). It must also be free of kinks or pits.
